Published Nov 21, 2026, 11:00 AM EST Ayush Pande is a PC hardware and gaming writer. When he's not working on a new article, you can find him with his head stuck inside a PC or tinkering with a server operating system. Besides computing, his interests include spending hours in long RPGs, yelling at his friends in co-op games, and practicing guitar. PLA may have been the filament I started my 3D printing journey with, but PETG quickly became my preferred option for turning STL files into tangible models. Sure, its glossy appearance makes it less enticing for aesthetically-pleasing models and cosplay props. But between its solid temperature resistance, tendency to absorb impact without shattering, and ability to withstand mild weather conditions, PETG is ideal for building functional prints. In fact, I’ve used PETG to design everything from simple replacement parts and household accessories to home lab cable management components, and these models have held up incredibly well for several months. However, I’d be lying if I said my PETG journey was smooth-sailing, especially because I had to get accustomed to its quirks after my PLA-only misadventures. Thankfully, I’ve since figured out some neat fixes to make the PETG printing process more bearable for my 3D printer as well as my sanity and wallet. Layer adhesion problems were the bane of my existence as a newcomer But a few slicer tweaks were all I needed to get perfect prints When I first got into 3D printing PETG models, I had a lot of trouble getting the first layer to stick to the build plate. And if the first layer didn’t stick, it’d cause the entire model to fail. Well, the first noob mistake I’d made was leaving the bed temperature far too low for the first and successive layers, even though I’d set the nozzle temps at the sweet spot of 240°C. Although upping the bed temps to 80°C resulted in better bed adhesion for the first layer, I’d still have minor layer adhesion problems, and those can be quite problematic for functional models. After realizing that a lot of the settings I’d imported from my PLA profile were terrible for PETG, I decided to create a new one from scratch. For example, my exhaust fan was running at 40% throughout the print, and it’d cause the freshly-extruded lines to cool down before it could fuse with other layers. So, I dialed it back to 0% for the initial layers and 10% for the rest of the model. Likewise, I dropped the print speeds to 35 mm/s to give the newly-melted filament more time to bond with the underneath layers. These fixes alone got rid of the layer adhesion issues for the majority of my prints, and I’ve started keeping separate PETG profiles with slightly tweaked properties to accommodate filaments from different manufacturers. Unfortunately, I still had another issue to take care of … PETG stringing can be contained with the right settings Drying the filament was the best way to curb its stringing tendencies The left model was printed with dried PETG, while the right one was made with an old (somewhat damp) PETG filament Despite calibrating my slicer’s PETG profiles to avoid layer adhesion problems, stringing was something that haunted me for a long time, and it only got worse as I kept using the same filament roll. As you may have guessed, a lot of the stringing problems were caused by my filament absorbing moisture, as PETG is hygroscopic in nature. And well, the average humidity in my backwater town ranges between 50–65%, and that’s just my living room. If I were to talk about the attic where I leave my 3D printers most of the time, this number climbs to 70% during monsoon, which is a death sentence for semi-used PETG rolls. Worse still, all the printers in my arsenal leave the spools on the side instead of storing them inside a plastic enclosure, making it a lot easier for them to absorb moisture. Combine all that with the fact that my functional PETG prints only consume a few dozen grams of the filament, and it’s no wonder my fledgling self had to deal with excessive stringing. Adding a filament dryer to my toolkit reduced the stringing problem considerably. These days, I just leave any unused PETG spool inside my dryer, while the rest of my filaments remain sealed inside bags with at least one desiccant bag. And if it’s been a while since I’ve used a PETG roll, I run the dryer for a few hours before feeding the filament to a 3D printer. That said, I have to admit that I still haven’t managed to completely remove stringing from my models. Sure, I don’t have to deal with cobwebs of plastic sticking all around my models, but I still encounter the occasional string or two around the open spaces on my prints. That’s why I keep my trusty heat gun around for PETG prints, as passing a heat gun quickly by the model gets rid of the minimal stringing. Although it took me a while to get the print quality right on my PETG models, it’s now the most used filament in my 3D printing arsenal. Despite providing solid impact toughness, temperature resistance, and weather durability, it’s a lot safer to print than typical industry-grade filaments. Plus, it's fairly affordable, and it satisfies my 3D printing needs.
PETG’s stringing and adhesion problems intimidated me at first, but fixing them only took a few minutes
Full Article
Original Source
Read the full article at Xda-developers →KhanList aggregates and links to publicly available news content. We do not host full articles from third-party sources. Always verify important information with original sources.